Fuers TL-2600 Fake Camera Instruction Manual

1. Produkti i Mbaruarview

The Fuers TL-2600 is a high-quality, durable dummy surveillance camera designed to deter potential intruders. It features a realistic appearance, a flashing LED light, and is suitable for both indoor and outdoor use. This device provides a cost-effective solution to enhance security visibility without the complexity of a real surveillance system.

Karakteristikat kryesore:

• Dizajn realist: High resemblance to actual security cameras.
• Dritë LED ndezëse: Simulates active surveillance, powered by 2 AAA batteries (not included).
• Ndërtim i qëndrueshëm: Made from high-quality ABS material, weather-resistant for outdoor use.
• Këndi i rregullueshëm: Features a mounting bracket allowing for 90° vertical and 360° horizontal rotation.
• Instalim i lehtë: No wiring required, mounts quickly to walls or ceilings.

Image 1.1: The Fuers TL-2600 Fake Camera featuring a red flashing LED light, simulating active operation.

Image 1.2: The camera's adjustable bracket allows for 90-degree vertical and 360-degree horizontal rotation for optimal positioning.

2. Përmbajtja e paketës

Ju lutemi verifikoni që të gjitha artikujt e listuar më poshtë janë të përfshirë në paketën tuaj:

• 1 x Fuers TL-2600 Dummy Camera Unit
• 1 x Mbështetëse Montimi (e para-bashkuar)
• 3 x Vida montimi
• 3 x priza muri
• 1 x CCTV Warning Sticker

Shënim: 2 x AAA batteries are nuk përfshihet dhe duhet të blihet veçmas.

Image 2.1: Contents of the package including the dummy camera, mounting hardware, and a CCTV sticker. Dimensions are also shown.

3. Konfigurimi

3.1 Instalimi i baterisë

1. Locate the battery compartment on the underside of the camera body.
2. Hapni me kujdes kapakun e ndarjes.
3. Insert two (2) AAA batteries (not included) into the compartment, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely. The LED light should begin flashing immediately.

Imazhi 3.1: View of the battery compartment opened to insert two AAA batteries.

Image 3.2: Step-by-step guide for installing batteries into the dummy camera.

3.2 Montimi i kamerës

1. Choose a suitable location for installation, such as a wall or ceiling, ensuring good visibility and deterrence.
2. Position the mounting bracket at the desired location and mark the three screw holes.
3. Drill pilot holes at the marked spots. For masonry or drywall, insert the provided wall plugs.
4. Siguroni kllapën e montimit në sipërfaqe duke përdorur vidat e dhëna.
5. Adjust the camera angle as needed (refer to Section 4.1).
6. Affix the included CCTV warning sticker in a prominent location nearby to further enhance deterrence.

4. Udhëzimet e funksionimit

4.1 Adjusting Camera Angle

The camera's mounting bracket allows for flexible positioning:

• Rregullimi vertikal: Loosen the side screw on the bracket to tilt the camera up or down (up to 90°). Tighten the screw once the desired angle is achieved.
• Rregullimi horizontal: The base of the bracket allows for full 360° rotation. Simply rotate the camera body to face the desired direction.

4.2 LED ndezje

Once batteries are correctly installed, the red LED light will automatically begin to flash continuously. There is no separate on/off switch for the LED. The flashing LED simulates the operation of a real security camera, enhancing its deterrent effect.

5. Mirëmbajtja

• Ndërrimi i baterisë: Replace the two AAA batteries when the LED light stops flashing or becomes dim. Always use fresh batteries for optimal performance.
• Pastrimi: Wipe the camera body and lens area with a soft, damp leckë për të hequr pluhurin dhe papastërtitë. Shmangni përdorimin e kimikateve të forta ose pastrues gërryes.
• Rezistenca ndaj motit: While designed for outdoor use, extreme weather conditions (e.g., heavy storms, prolonged direct sunlight) may affect its lifespan. Periodically check the unit for any signs of wear or damage.

6. Troubleshooting

• LED Not Flashing:
  • Kontrolloni nëse bateritë janë instaluar saktë me polaritetin e duhur.
  • Zëvendësoni me bateri të reja AAA.
• Camera Feels Loose After Mounting:
  • Sigurohuni që të gjitha vidat e montimit të jenë shtrënguar mirë.
  • If mounted on drywall, ensure wall plugs are properly seated.

7. Specifikimet