Produkti Mbiview
The Cartell CP4 Vehicle Sensor Kit is an electronic vehicle detection device designed for automatic gate release. It operates based on the science of electromagnetic induction, detecting the movement of a vehicle to trigger gate operation. This system is supplied with underground burial cable and is specifically designed to respond to vehicles, making it unsuitable as a hold-open loop.
Instalimi dhe konfigurimi
Proper installation is crucial for the optimal performance of your Cartell CP4 sensor. Follow these guidelines carefully:
Vendosja e sensorit:
- The sensor is designed to cover a 12-foot wide driveway from the side of the drive.
- Position the sensor approximately 80 to 100 feet from the gate, depending on the length of the supplied cable (available in 100', 200', 300', or 500' lengths).
- Bury the sensor unit and its connecting pipe 3 to 5 inches below the surface.
Figure 1: Installation instructions and diagrams from the back of the product box, detailing sensor placement and wiring.
Mbrojtja e kabllove:
- Insert the 1/2-inch PVC pipe inside the slip joint of the sensor. DO NOT GLUE.
- Smooth out the entire length of the cable and gently pull it through a 1/2-inch PVC pipe. This protects the cable underground.
- SHËNIM: Warranty may be void if the cable is not run in conduit.
Figure 2: The Cartell CP4 sensor unit with its extensive coiled cable, ready for installation.
Figura 3: Një detaj i detajuar view of the Cartell CP4 sensor unit, highlighting its robust design.
Wiring (CP-4):
The CP4 sensor requires a power supply of 8-24 VAC or 8-30 VDC. The current draw is 30-70 µA in standby and 40-60 mA during alarm.
| Ngjyra e telit | Dual Exit Terminal | Single Exit Terminal |
|---|---|---|
| E kuqe | Fuqia + | Fuqia + |
| E zezë | Power - | GND or COM |
| E bardha | E zakonshme | GND or COM |
| Blu | Exit N.O. | Free Exit or Open Terminal |
| E verdha | Exit N.C. | (Not used for single exit) |
For single exit terminal setups, the yellow wire is typically not used. Connect the black and white wires to a common ground, the red wire to the positive power supply, and the blue wire to the free exit or open terminal on your gate operator's control board.
Parimet e funksionimit
The Cartell CP4 sensor utilizes electromagnetic induction to detect the presence of a vehicle. When a vehicle passes over the buried sensor, it triggers a signal to the gate operator, initiating the gate opening sequence. This system is designed for automatic gate release, providing a convenient exit without requiring manual intervention.
Figure 4: Illustration of a vehicle approaching a gate, demonstrating the sensor's function in triggering the gate to open automatically.
Rregullimi i ndjeshmërisë:
In most cases, it is not necessary to adjust the sensor's sensitivity or remove its lid. The sensitivity is set to "High" by default (dip switch in "OFF" position). If adjustment is required, refer to the dip switch settings below:
- High (Default): Detects vehicles going 5 MPH 12-14 feet away. (Dip switches 1 & 2 OFF)
- E mesme: Detects vehicles going 5 MPH 6-8 feet away. (Dip switch 1 ON & 2 OFF)
- E ulët: Detects vehicles going 5 MPH 2-3 feet away. (Dip switches 1 & 2 ON)
Mirëmbajtja
The Cartell CP4 sensor is designed for durability and minimal maintenance. Ensure the area around the buried sensor and cable remains clear of heavy debris or obstructions that could interfere with its operation or damage the conduit. Regular visual inspection of exposed wiring and connections is recommended to ensure integrity.
Zgjidhja e problemeve
If you encounter issues with your CP4 sensor, first verify all wiring connections according to the diagram in the Setup section. Ensure the sensor is buried at the correct depth and distance from the gate. For more detailed troubleshooting steps, including product issues that may require removing the sensor, please download the full online manual from www.cartell.com ose skanoni kodin QR të dhënë në paketimin e produktit.
For technical support, you may call Cartell at 717-832-0033.
Specifikimet
| Veçori | Detaj |
|---|---|
| Gama maksimale | 100 Feet (cable length dependent) |
| sensor Technology | Electromagnetic Induction Sensor |
| Fuqia e kërkuar | 6-31 VAC ose 8-46 VDC |
| Relay Trip Time | 2 sekonda |
| Pesha e artikullit | 4.4 paund |
| Dimensionet e paketës | 16.3 x 8.23 x 3.03 inç |
| Numri i modelit | CP3-300 |
| Prodhuesi | Cartell |
| Ngjyra | E zezë |
Garancia dhe Mbështetja
Cartell provides support for its products. As noted in the installation section, the product warranty may be void if the cable is not run in conduit. For any technical assistance or product inquiries, please contact Cartell directly. You can also find additional resources and the full online manual on the official Cartell webfaqe.
- Mbështetje Teknike: 717-832-0033
- zyrtare Webfaqja e internetit për manualet: www.cartell.com
