Manuali i Udhëzimeve për Setin e Gimbaleve CNC Hall RadioMaster AG02

Hyrje

This manual provides detailed instructions for the installation, operation, and maintenance of your RadioMaster AG02 CNC Hall Gimbals Set. Designed for precision and durability, these gimbals are compatible with RadioMaster TX16, TX15, and Boxer radio controllers, offering an enhanced control experience for your aircraft. Please read this manual thoroughly before use to ensure proper function and longevity of your product.

Produkti Mbiview

The RadioMaster AG02 CNC Hall Gimbals Set features advanced design and engineering for superior performance:

• Full Aluminum Construction: Optimized structural areas reduce rotational inertia by over 20% while maintaining rigidity, providing smoother and more responsive control.
• Next-Generation Low-Noise Hall Sensors: Deliver ultra-fast response without compromising accuracy or stability.
• Adjustable Travel: Vertical and horizontal travel adjustment allows for personalized feel for any pilot.
• Quad Precision Bearings: Ensure unparalleled stick feel and smooth operation.
• 100% Mounting Compatibility: Directly installable as an upgrade for existing full-size RadioMaster gimbals without modifications.
• Projektuar për: RadioMaster TX16, TX15, and Boxer Radio Controllers.

Informacioni i Sigurisë

The product is not intended for use by children. Always handle with care and ensure proper installation to prevent damage to the gimbals or your radio controller.

Përmbajtja e paketës

Verifikoni që të gjitha artikujt e listuar më poshtë janë të pranishëm në paketën tuaj:

• 1 Pair of AG02 CNC Hall Sensor Gimbals
• 2 * High Tension Springs
• 1 * GH1.25-SH1.25 adapter board (for Boxer/TX16sMKII)
• 4 * PB2.3*10 Mounting Screws
• 1 * Hex Wrench
• 1 * User Manual (this document)

Konfigurimi dhe instalimi

Follow these steps to install your AG02 CNC Hall Gimbals into your compatible RadioMaster radio controller.

1. Përgatitja: Ensure your radio controller is powered off and disconnect any power sources.
2. Access Gimbal Bay: Carefully open your radio controller to access the existing gimbals. Refer to your radio controller's specific manual for instructions on how to safely open the casing.
3. Remove Old Gimbals: Disconnect the wiring and unscrew the mounting screws holding the old gimbals in place.
4. Install AG02 Gimbals: Position the new AG02 gimbals in the gimbal bays. Use the provided PB2.3*10 mounting screws to secure them.
5. Lidhni instalimet elektrike: Connect the gimbal wiring to the appropriate ports on your radio controller's main board. If installing into a Boxer or TX16sMKII, use the provided GH1.25-SH1.25 adapter board if necessary. Ensure connections are secure and correctly oriented.
6. Close Radio Controller: Carefully reassemble your radio controller, ensuring no wires are pinched.
7. Kalibrimi: After installation, power on your radio controller and perform a gimbal calibration as per your radio controller's firmware instructions. This ensures accurate response and full travel range.

Image: The AG02 CNC Hall Gimbals. The left gimbal shows the stick in a neutral position, while the right gimbal shows the stick tilted, illustrating the range of motion. Both units feature red anodized aluminum frames and precision internal components.

Udhëzimet e funksionimit

Once installed and calibrated, the AG02 gimbals operate seamlessly with your RadioMaster radio controller. The following adjustments can be made:

• Adjustable Travel: The gimbals feature vertical and horizontal travel adjustment. Use the included hex wrench to fine-tune the travel limits to your preference. Refer to the markings on the gimbal frame for precise adjustments.
• Throttle Mode Switch (Mode 1/2): The throttle mode can be switched without disassembling the gimbal. Consult your radio controller's manual for specific instructions on how to change the throttle mode and adjust the tension.
• Rregullimi i tensionit të pranverës: Spring tension can be adjusted without disassembling the gimbal. Use the hex wrench to modify the spring tension to achieve your desired stick feel.

Mirëmbajtja

To ensure the longevity and optimal performance of your AG02 gimbals, follow these maintenance guidelines:

• Pastrimi: Keep the gimbals free from dust and debris. Use a soft, dry cloth to gently wipe the surfaces. Avoid using liquid cleaners or solvents.
• Inspektimi: Periodically inspect the gimbals for any signs of wear, loose screws, or damage. Address any issues promptly.
• Magazinimi: When not in use, store your radio controller in a clean, dry environment away from extreme temperatures and direct sunlight.

Zgjidhja e problemeve

If you encounter issues with your AG02 gimbals, consider the following:

• Inaccurate Response/Drifting: Recalibrate the gimbals through your radio controller's firmware settings. Ensure all wiring connections are secure.
• Stiff or Loose Stick Feel: Adjust the spring tension as described in the Operating Instructions section.
• Limited Travel: Check the physical travel adjustment screws and ensure they are not overly restrictive. Perform a calibration after any adjustments.
• Asnjë përgjigje: Verify that the gimbals are correctly wired and securely connected to the radio controller's main board. Check for any visible damage to the wiring or connectors.

If problems persist, contact RadioMaster customer support or your authorized dealer for further assistance.

Specifikimet

Garancia dhe Mbështetja

For warranty information or technical support, please refer to the official RadioMaster webnë vend ose kontaktoni shitësin tuaj të autorizuar. Ruajeni provën e blerjes për kërkesat e garancisë.