Stem Aria Linear Light

KUJDES

PARA INSTALIMIT

Please read the provided step-by-step instructions thoroughly before proceeding with the installation. You will achieve a secure and successful installation by taking these precautions and diligently following the provided guidelines.

1. Mbani mend gjithmonë të fikni furnizimin me energji në qark përpara se të filloni ndonjë punë instalimi. Detyrat e instalimit elektrik duhet të kryhen ekskluzivisht nga një kontraktues i autorizuar elektrik. Për udhëzime profesionale, ju lutemi kontaktoni autoritetin tuaj lokal të energjisë elektrike.
2. Përpara instalimit, kontrolloni zonën e instalimit për praninë e ndonjë kablloje tjetër për të parandaluar dëmtimin e instalimeve elektrike të fshehura.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light up to 3kg ( 6.6 lbs, aluminium)/ 7kg (15.4 lbs, brass).
4. Ju lutemi vini re se kjo pajisje është projektuar për përdorim vetëm në mjedise të brendshme të thata shtëpiake.
5. When handling the metal fixture, make sure your hands are clean. It is advised to wear gloves to prevent leaving marks on the metal surface.
6. Periodically check screws and connections for stability. Gently tighten if necessary, avoid over-tightening.

UDHËZIME KUJDESI

Sigurohuni që duart tuaja të jenë të pastra përpara se të prekni sipërfaqen metalike për të shmangur lënien e shenjave të gishtërinjve. Këshillohet përdorimi i dorezave kur përdorni pajisjen e ndriçimit. Mos përdorni asnjë lëndë gërryese në produkt. Ju lutemi kini kujdes me peshën e tij. Trajtoni me kujdes.

Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface.

DETAJE TEKNIKE

• Dimensionet
  • Dia.. 26 L1440 MM
  • Dia 1 L56.7 IN (Custom length on request)
• Materiali & Pesha
  • Cast Aluminium – 2.5 kg
  • Cast Brass – 6 kg
• Vlerësimi Kelvin 3000K
• Burim drite
  IND/ UK/ EU LED strip (Incl.)12W, 220-240V
• Classification IP20
• Prerje faze e errësueshme, kompatibile me TRIAC
• Hardware
  W56 H32 D140 MM W2.2 H1.3 D5.5 IN Aluminium, Brass finish
• Kordoni
  • Lidhje e fortë
  • Cord length – 2000 MM

BRENDA KUTI

* Driver and LED light are not included for regions with a voltagKërkesa prej 110-120V.

(Fig. 1)

HAPI 1

Position and drill

Carefully mark the position where you intend for the light fixture to hang. Use the dimensions marked (Fig. 1) as a guide to drill holes in the ceiling, then proceed to the next step.

(Fig. 2)

HAPI 2

Install the Clutch wire gripper and Canopy back plate

1. Connect the clutch wire gripper (A1) and canopy back plate (B) by fastening them at the drilled holes in the ceiling using the drywall screws (Fig. 3).
2. Insert the clutch wire (C) through the clutch wire screw (D)(Fig. 4), fitted on the ends of the cast Rod.
3. Secure the opposite end of the clutch wire gripper (A1)(Fig. 3).
   1. To ensure the safe suspension of the light fixture, check that the wires are firmly attached to the clutch wire grippers and are devoid of any slack.

(Fig. 5)

HAPI 3

Install the second Clutch wire gripper

Take the second clutch wire gripper (A2) and fasten it directly onto the ceiling (Fig. 6) using the drywall screw. Now insert the clutch wire (C) through the clutch wire screw (D) (Fig. 4) and securely attach it to the clutch wire gripper (A2) (Fig. 6).

(Fig. 7)

HAPI 4

Install and level the Rod

Fasten the clutch wire screw (D) to both ends of the Rod (Fig. 7) and adjust its height as desired. Ensure that the light fixture is in alignment with the floor.

(Fig. 8)

HAPI 5

Connect the wiring to the driver

1. Insert the LED cord end (F) on the Rod through the hole in the canopy casing (E) and connect it to the driver output mounted on the ceiling (Fig. 8).
2. Connect the driver input to the electrical connection in the ceiling (Fig. 9).
   Ensure that all connections are secure and that there are no exposed wires or electrical hazards. Pay attention to the polarity of the connection. A wrong connection can cause damage.

(Fig. 10)

HAPI 6

Close the Canopy casing

After completing the installation, take the canopy’s top cover and attach it to the back plate (Fig. 10) using the canopy screws (Fig. 11). Ensure that the wiring and any excess clutch wire strands are neatly trimmed after the installation.

In case you require further assistance, please write to us at info@stemdesign.co.

Pyetjet e bëra më shpesh

A mund të përdoret pajisja jashtë?

No, the fixture is designed for use in dry domestic indoor environments only.

Çfarë përfshihet në kuti?

The box includes light source, hardware, cord, wall plugs, drywall screws, clutch wire gripper, clutch wire, gloves, canopy casing with driver, rod with LED light, and clutch wire screws.

Is the driver and LED light included for all regions?

Driver and LED light are not included for regions with voltagKërkesa prej 110-120V.

Dokumentet / Burimet

kërcell Aria Linear Light [pdf] Manuali i Udhëzimeve Dritë lineare Aria, Dritë lineare, Dritë

Referencat

• Manuali i Përdoruesit